Version |
ID |
Typ |
Changelog
|
7.08.010 |
17280 |
Feature |
IEC61850 MMS Server - Creating more Specified CALH Nodes
|
7.08.010 |
16395 |
Feature |
PSX210: Enable NTP
|
7.08.010 |
16757 |
Feature |
IEC61850 MMS server - better representation of node LCCH for single instance communication channels
|
7.08.010 |
16755 |
Feature |
IEC61850 MMS server - verbosity settings
|
7.08.010 |
16654 |
Feature |
IEC61850 MMS server - Error handling improvement for the MMS server
|
7.08.010 |
17413 |
Feature |
New URI features for ZTP autoconfig
|
7.08.010 |
17277 |
Feature |
Support for REL1002 with Source Selection
|
7.08.010 |
16653 |
Feature |
IEC61850 MMS server - Add logical node CALH for alarm handling in the MMS server,,CALH', defined by IEC61850-7-4 (ed 2.1) chapter 6.5.2 This node reflects alarms and warnings of the IMS clocks. Those events are read via lt\_cli out of the path /status/notification/events,,,,,,,,,,,
|
7.08.010 |
15879 |
Feature |
IEC61850 MMS server - include all virtual interfaces into the IEC61850 clock model as logical nodes
|
7.08.010 |
15861 |
Feature |
IEC61850 MMS server - MMS icd-file: Include all logical interfaces in the section
|
7.08.010 |
15698 |
Feature |
IEC61850 REL1000 support
|
7.08.010 |
14442 |
Feature |
IEC61850 MMS server - Log Remote IP Endpoint when a client connection is established
|
7.08.010 |
17230 |
Bug |
DHCP IP addresses correctly indicated on PRP interfaces
|
7.08.010 |
17016 |
Bug |
CLI: read Mrs-Priorities values correctly from Config after a commit
|
7.08.010 |
17382 |
Bug |
Update of curl to 8.7.1
|
7.08.010 |
17302 |
Bug |
Update of Linux-PAM to version 1.6.0
|
7.08.010 |
17286 |
Bug |
Update of gnutls to version 3.8.4
|
7.08.010 |
17062 |
Bug |
Update of bind utils to 9.16.48
|
7.08.010 |
17013 |
Bug |
Update of shadow to 4.14.5
|
7.08.010 |
16857 |
Bug |
Update of libxml2 to 2.11.7
|
7.08.010 |
16856 |
Bug |
Update of expat to 2.6.2
|
7.08.010 |
17161 |
Bug |
CLI: fixed set-time
|
7.08.010 |
17002 |
Bug |
Fix PRP interface after power cycle
|
7.08.010 |
17001 |
Bug |
Fix defunct process spawned again after triggering the Test notification
|
7.08.010 |
16918 |
Bug |
SNMP: Improve NTP request count under high load
|
7.08.010 |
16905 |
Bug |
Syncmon: ntp counter drops to 0 under high load
|
7.08.010 |
16155 |
Bug |
CLI: fixed pzf receiver options
|
7.08.010 |
14396 |
Bug |
PSX: fix state when Tel G.8275.2 or Layer 2 profiles are used
|
7.08.009 |
16949 |
Bug |
Fixed missing start of MMS server in case it was activated
|
7.08.008 |
16564 |
Feature |
REST-API: Allow to specifiy API version in header of API requests
|
7.08.008 |
12837 |
Feature |
Support for new clock model GXL183
|
7.08.008 |
16666 |
Bug |
REST/CLI: Fixed Unicast cluster member configuration
|
7.08.008 |
16594 |
Bug |
CLI: Fixed IPv6 cluster status
|
7.08.008 |
16587 |
Bug |
SyncMon: Fixed calculation of mean CN ratio
|
7.08.008 |
16560 |
Bug |
Avoid crash of management service if API request modules that do not exist
|
7.08.008 |
15204 |
Bug |
CLI/REST: Removed 'unkown' property in 'antenna' object
|
7.08.008 |
16875 |
Bug |
No wait for input during boot
|
7.08.008 |
16810 |
Bug |
Update of curl to 8.6.0
|
7.08.008 |
16793 |
Bug |
Update of openssl to 3.0.13
|
7.08.008 |
16684 |
Bug |
Update of zlib to 1.3.1
|
7.08.008 |
16670 |
Bug |
Update of gnutls to 3.8.3
|
7.08.008 |
16574 |
Bug |
WEB/PTP: Prevent misconfiguration and inconsistent display of settings for PSX210
|
7.08.008 |
16659 |
Bug |
Fixed CLI and REST API service on LTOS-light version
|
7.08.008 |
16644 |
Bug |
CLI/REST: Fixed misleading cluster state info
|
7.08.008 |
16601 |
Bug |
Fixed enabled state for delete user button on user admin page
|
7.08.008 |
16579 |
Bug |
Avoid CLI startup fault on SyncFire units
|
7.08.008 |
16575 |
Bug |
Fixed gateway config for IPv6 cluster
|
7.08.008 |
16536 |
Bug |
CLI: Fixed import of configuration
|
7.08.008 |
16533 |
Bug |
CLI/REST: Fixed return value of clk module ref-type
|
7.08.008 |
16125 |
Bug |
Fixed backplane and systype info in 'show hwid' on some systems
|
7.08.008 |
15363 |
Bug |
SyncMon: Apply change of source port in NTP monitoring config directly after save command
|
7.08.007 |
16171 |
Feature |
REST/CLI: Support status of NTP Cluster via API
|
7.08.007 |
16132 |
Feature |
Support new module LNE/SFP200
|
7.08.007 |
16525 |
Feature |
Support configuration of user defined PTP Clock Variance
|
7.08.007 |
16267 |
Feature |
CLI/REST: Support enabling NTS option for external servers via API
|
7.08.007 |
15906 |
Feature |
Support for extended GNSS SV modes
|
7.08.007 |
1791 |
Feature |
Support for IPv6 in NTP Cluster
|
7.08.007 |
16490 |
Bug |
REST/CLI: Fixed Unicast cluster member configuration
|
7.08.007 |
16488 |
Bug |
Fixed occurences of zombie processes when using send_email script
|
7.08.007 |
16429 |
Bug |
CLI/REST: Avoid crash of fastapid after last SyncMon node has been deleted
|
7.08.007 |
16226 |
Bug |
Update of net-snmp to 5.9.4.rc1
|
7.08.007 |
16204 |
Bug |
Limit number of SANs for CSR or certificate generation to 100
|
7.08.007 |
16196 |
Bug |
Fixed display of MRS status for 2nd clock in Web UI
|
7.08.007 |
15804 |
Bug |
Update of syslog-ng to 4.3.1
|
7.08.007 |
15707 |
Bug |
Update of OpenSSH to 9.5p1
|
7.08.007 |
15695 |
Bug |
NTP: Do not drop packets with low poll values
|
7.08.007 |
16521 |
Bug |
Update of sudo to 1.9.15p5
|
7.08.007 |
16462 |
Bug |
Update of libssh to 0.9.8
|
7.08.007 |
16451 |
Bug |
Update of OpenSSH to 9.6p1
|
7.08.007 |
16312 |
Bug |
Update of tar to 1.35
|
7.08.007 |
16311 |
Bug |
Update of curl to 8.5
|
7.08.007 |
16306 |
Bug |
RootCA bundle updated to version: Dec 12 04:12:04 2023
|
7.08.007 |
16280 |
Bug |
Grey-out optional passphrase of Certificates in Web UI for info users
|
7.08.007 |
16270 |
Bug |
Update of proftpd to 1.3.8b SSH attack (CVE-2023-48795).
|
7.08.007 |
16266 |
Bug |
Update of gzip to 1.13
|
7.08.007 |
16264 |
Bug |
Update of d-bus to 1.12.28
|
7.08.007 |
16262 |
Bug |
Update of bash to 5.2.21
|
7.08.007 |
16260 |
Bug |
Update of Linux-Pam to 1.5.3
|
7.08.007 |
15794 |
Bug |
Update of inetutil to 2.5
|
7.08.007 |
15789 |
Bug |
Update of OpenSSL to 3.0.12
|
7.08.007 |
15519 |
Bug |
Update of glib to 2.78.0
|
7.08.007 |
16514 |
Bug |
Fixed return value of snmp object mbgLtNgRefclockTimeDiff
|
7.08.007 |
16501 |
Bug |
Remove Cluster information in API in case all Clusters are deactivated
|
7.08.007 |
16275 |
Bug |
CLIHELP: Added infos for nts-cfg
|
7.08.007 |
16205 |
Bug |
WEB UI: Increased Cookie size
|
7.08.006 |
15955 |
Feature |
Removed libs and tools for netconfig
|
7.08.006 |
14379 |
Feature |
Include ethtool output for every interface in diagnostic file
|
7.08.006 |
12482 |
Feature |
Include XHE infos and states in diagnostic files
|
7.08.006 |
16163 |
Bug |
Handle state of BITS-IN input on ESI cards correctly
|
7.08.006 |
16150 |
Bug |
Avoid crash after CLI commit for FDM config
|
7.08.006 |
15828 |
Bug |
Support additional satellite systems like QZSS and SBAS on GXL183
|
7.08.006 |
16165 |
Bug |
Apply restored config on FDM cards
|
7.08.006 |
16121 |
Bug |
CLI/REST: Fixed config option for transmitter distance for 2nd refclock
|
7.08.005 |
1331 |
Feature |
Introduced additional confirmation button after 'Rescan Refclocks' command has been executed
|
7.08.005 |
15924 |
Bug |
CLI/REST: Fixed HPS100 config on M500
|
7.08.005 |
15896 |
Bug |
Fixed ESI card config validation in Web UI
|
7.08.005 |
15895 |
Bug |
Fixed state labels for LIU cards in Web UI
|
7.08.005 |
15863 |
Bug |
Prevent unnecessary restarts of the NTP service when the NTS server mode is disabled on devices with Atom CPU
|
7.08.005 |
15770 |
Bug |
CLI/REST: Avoid inconsistencies of 'selected satellites' information
|
7.08.005 |
15757 |
Bug |
CLI/REST: Update default gateway config on changes correctly
|
7.08.005 |
16203 |
Bug |
CLI: Fixed memory leak on loading config
|
7.08.005 |
16095 |
Bug |
REST-API not offered on LTOS-light versions anymore due to RAM usage
|
7.08.005 |
16013 |
Bug |
IO Card config will be sent to the correct card if more than one card of the same type is installed
|
7.08.005 |
15946 |
Bug |
Fixed faillock for authentication for REST-API
|
7.08.005 |
15942 |
Bug |
Fixed upload procedure and error handling of a signed HTTPS certificate
|
7.08.005 |
15911 |
Bug |
CLI/REST: Fixed response code for failed start-update command
|
7.08.005 |
15901 |
Bug |
WEB: Fixed Antenna notifications on MSF systems
|
7.08.005 |
15889 |
Bug |
Avoid removal of routing rules after CLUSTER state change
|
7.08.005 |
15878 |
Bug |
CLI/REST: Support for BPE mode BPE-2352
|
7.08.005 |
15871 |
Bug |
E-Mail notifications did not work with some mail servers (empty mail body)
|
7.08.005 |
15866 |
Bug |
send_mail service is now sendig correct EHLO name
|
7.08.005 |
15865 |
Bug |
Fixed broken 'Details' link in NTP Client list of Web UI
|
7.08.005 |
15859 |
Bug |
Fixed SNMP call to mbgLtNgCfgNumberOfVirtualIf object
|
7.08.005 |
15853 |
Bug |
Fixed SNMP call to mbgLtNgEthPortLinkState if port is not present
|
7.08.005 |
15821 |
Bug |
Fixed SNMP call for NTP stratum
|
7.08.005 |
15817 |
Bug |
Fixed display of MRI card information in WEB UI
|
7.08.005 |
15814 |
Bug |
Fixed SNMP responses that errornously contained a '=' sign
|
7.08.005 |
15799 |
Bug |
Trigger Alarm LED only on selected events
|
7.08.005 |
13806 |
Bug |
Show status for lldp even if lldp is stopped
|
7.08.004 |
15685 |
Feature |
CLI/REST: Expose NTS server configuration
|
7.08.004 |
15701 |
Bug |
Update of curl to 8.4.0
|
7.08.004 |
15754 |
Bug |
CLI/REST API: Corrected returned error codes for hidden menus
|
7.08.004 |
15660 |
Bug |
CLI: Avoid showing ESI card notification config if card is not present
|
7.08.003 |
14083 |
Task |
SyncMon uses REST API to communicate with microSync
|
7.08.003 |
15632 |
Feature |
MMS: Allow possibility to rename the logical device
|
7.08.003 |
15422 |
Feature |
WEB UI: Create registration file for Fugro Atomichron service
|
7.08.003 |
13986 |
Feature |
Support (non-standard) local time offset for PTP (requires HPS FW >= 2.1.4)
|
7.08.003 |
1304 |
Feature |
Secured e-Mail transport with TLS
|
7.08.003 |
15655 |
Feature |
Restructured overview of notification event matrix in web UI
|
7.08.003 |
15633 |
Feature |
MMS: Enabled possibility to use prefixes for logical nodes
|
7.08.003 |
15508 |
Feature |
Harmonized tab layout on IOConfig page in Web UI
|
7.08.003 |
15485 |
Feature |
CLI/REST: Support for IMS module REL
|
7.08.003 |
15385 |
Feature |
Show clock sensors in Web UI
|
7.08.003 |
15192 |
Feature |
Show Fugro Atomichron information in case a compatible clock module is used
|
7.08.003 |
14703 |
Feature |
CLI/REST: submenu gnss-constellation added to /configuration/chassis0/slots/[SLOT-ID]/module/satellites for clocks
|
7.08.003 |
14455 |
Feature |
MMS: Adjusted content in ICD Header
|
7.08.003 |
13822 |
Feature |
CLI: Added output parameter to export function
|
7.08.003 |
15381 |
Bug |
CLI: calling 'export --help' prints the help of the export-command
|
7.08.003 |
15359 |
Bug |
Update of OpenSSH to 9.4p1
|
7.08.003 |
15221 |
Bug |
Support PTP and GPS PCI card together within one SyncFire
|
7.08.003 |
15073 |
Bug |
Fixed initial refclock time string format on RDT systems
|
7.08.003 |
14804 |
Bug |
Fixed NTP Client List in Web UI
|
7.08.003 |
14721 |
Bug |
PTP: Prevent crashes in rare cases when the selection of a PTP slave module changes
|
7.08.003 |
14715 |
Bug |
"Web UI: Fixed ""Time Code Line"" config option for VSI cards"
|
7.08.003 |
14652 |
Bug |
Web UI/Docs & Support: Fixed display of available documents
|
7.08.003 |
14607 |
Bug |
REST API: Fixed viewing a submenu's capabilities
|
7.08.003 |
2707 |
Bug |
Support for module LSG180
|
7.08.003 |
15521 |
Bug |
Update of json-c to 0.17
|
7.08.003 |
15490 |
Bug |
Multithreaded NTP Server: Do not bind internally used helper socket to wildcard address
|
7.08.003 |
15486 |
Bug |
No wait for input during boot
|
7.08.003 |
15269 |
Bug |
Update of OpenSSL to 1.1.1w
|
7.08.003 |
15234 |
Bug |
RootCA bundle updated to version: Aug 22 03:12:04 2023
|
7.08.003 |
15232 |
Bug |
Update of Linux kernel to 4.14.325
|
7.08.003 |
15215 |
Bug |
Improved pam tacacs+ authorization step
|
7.08.003 |
15024 |
Bug |
Update of curl to 8.3.0
|
7.08.003 |
15658 |
Bug |
Avoid unnecessary log entries in auth.log
|
7.08.003 |
15525 |
Bug |
Allow ' char in passphrase of SNMP v3 trap
|
7.08.003 |
15517 |
Bug |
CLI: Support antenna state for x182 and x183 clock models
|
7.08.003 |
15365 |
Bug |
Show status flags of 2nd TCR clock on main page
|
7.08.003 |
15357 |
Bug |
Provide correct 'estimated time quality' value in holdover
|
7.08.003 |
15342 |
Bug |
Show correct reference led color if two TCR clocks are used
|
7.08.003 |
15322 |
Bug |
Support reserved MRS precision value '999999999' to exclude source from being selected
|
7.08.003 |
15298 |
Bug |
CPU modules in LCES systems now handle redundant power supply detection correctly again
|
7.08.003 |
15237 |
Bug |
Show all manually added users in web UI except the default system user
|
7.08.003 |
15223 |
Bug |
CLI/REST: Show correct sync state in GNM antenna state
|
7.08.003 |
15217 |
Bug |
NTP: Ensure that the multithreaded NTP server starts successfully while configured IPv6 addresses are still in the tentative state
|
7.08.003 |
15198 |
Bug |
CLI/REST: Do not offer MRS information on non-MRS systems
|
7.08.003 |
15145 |
Bug |
Command to register ports for a service avoids registering existing ports multiple times
|
7.08.003 |
15133 |
Bug |
CLI/REST: Fixed ping command
|
7.08.003 |
15130 |
Bug |
CLI/REST: Do not use local host address for gateway and nameserver in case no entries are present
|
7.08.003 |
15128 |
Bug |
CLI/REST: Return the correct color of the alarm LED
|
7.08.003 |
15108 |
Bug |
NTP: Ensure that two servers can query each other as a fallback
|
7.08.003 |
15107 |
Bug |
CLI/REST: Fixed service status command
|
7.08.003 |
15094 |
Bug |
NTP: Ensure that the multithreaded NTP server is always restarted correctly
|
7.08.003 |
15062 |
Bug |
Multithreaded NTP server: Ensure that firewall rules are always setup correctly
|
7.08.003 |
15055 |
Bug |
CLI/REST: Return error messages in JSON format at all times
|
7.08.003 |
15049 |
Bug |
Remove possibility to disable all GNSS systems on Multi-GNSS receivers
|
7.08.003 |
15038 |
Bug |
Use static default gateway setting even if DHCP is used and compatible
|
7.08.003 |
15020 |
Bug |
Fixed removal of additional e-Mail recipients
|
7.08.003 |
14758 |
Bug |
CLI: Fixed configuration of PPO-PPS pulse length
|
7.08.003 |
14742 |
Bug |
CLI/REST: Fixed info for 'good' and 'in view' satellites
|
7.08.003 |
14519 |
Bug |
Fixed update of net.cfg after import of config backup
|
7.08.003 |
14486 |
Bug |
Fixed gateway setup for NTP Cluster interfaces
|
7.08.003 |
14436 |
Bug |
MMS: Fixed display of meanPathDelay
|
7.08.003 |
14435 |
Bug |
MMS: Fixed TimeSrc info in case PTP is the source
|
7.08.003 |
14403 |
Bug |
Fixed SNMP error when querying mbgLtNgCfgPtpTable
|
7.08.003 |
14334 |
Bug |
Extended functionality for 'show ptp' command
|
7.08.003 |
14333 |
Bug |
REST API: Added error message for paths that are not found in case a regex is used
|
7.08.003 |
14253 |
Bug |
Corrected order of network interfaces on SyncFire SF1500
|
7.08.003 |
13354 |
Bug |
Fixed 2nd serial COM port for RDT systems
|
7.08.003 |
13158 |
Bug |
FDM511: Fixed false positive FDM error after system boot
|
7.08.003 |
12443 |
Bug |
Fixed FDM frequency deviation value sent via network
|
7.08.002 |
13990 |
Feature |
Made UTC parameters available for VSI card
|
7.08.002 |
14391 |
Feature |
Graphics Magick (gm) removed from firmware image
|
7.08.002 |
13731 |
Feature |
PSX210: Update admin password if LTOS root password is changed
|
7.08.002 |
14615 |
Feature |
Support for Oregano PCIe card syn1588NIC V.2.3 on SyncFire
|
7.08.002 |
14330 |
Feature |
Added support for IMS module CPE182
|
7.08.002 |
13879 |
Feature |
CLI/REST: Support for IMS module CPE
|
7.08.002 |
13309 |
Feature |
SyncMon: Added VSG OSC value in SystemMonitoring
|
7.08.002 |
13075 |
Feature |
REST API: Introduced interface to use Bearer Token for authorization
|
7.08.002 |
12110 |
Feature |
CLI/REST: Support for CPE modules
|
7.08.002 |
6129 |
Feature |
Support for IEC 61850 MMS
|
7.08.002 |
14629 |
Bug |
Added serial string types to UI that were missing on selected systems
|
7.08.002 |
14508 |
Bug |
New leapsecond file expires on 28 June 2024
|
7.08.002 |
14296 |
Bug |
Added alarm notification if ntpd or ntpsrv are not startet
|
7.08.002 |
14276 |
Bug |
Support reset of individual ports on LNE180SFP
|
7.08.002 |
14257 |
Bug |
Only allow user names with characters that are POSIX compatible
|
7.08.002 |
13988 |
Bug |
PTP: Prevent lockups when a PSX210 card is unresponsive
|
7.08.002 |
13487 |
Bug |
PSX210: Add support for monitoring each network interface individually
|
7.08.002 |
14387 |
Bug |
Avoid increasing resource consumption of ifmonitor
|
7.08.002 |
14623 |
Bug |
Update of OpenSSH to 9.3p2
|
7.08.002 |
14459 |
Bug |
Improved signature verification
|
7.08.002 |
14364 |
Bug |
Update of GnuTLS to 3.8.0
|
7.08.002 |
14310 |
Bug |
Update of libssh to 0.9.7
|
7.08.002 |
14187 |
Bug |
Update of OpenSSL to 1.1.1u
|
7.08.002 |
14167 |
Bug |
Update of curl to 8.1.2
|
7.08.002 |
14155 |
Bug |
Update of ncurses to 6.4-20230610
|
7.08.002 |
13890 |
Bug |
Improved security checks while downloading a leap second file
|
7.08.002 |
13827 |
Bug |
SyncMon: Correctly display and save HTTPS and peer certificate verification settings for external microSync nodes
|
7.08.002 |
12418 |
Bug |
Update of net-snmp to 5.9.4pre3
|
7.08.002 |
14320 |
Bug |
Update of ntpd to 4.2.8p17
|
7.08.002 |
14313 |
Bug |
Update of cpio to 2.14
|
7.08.002 |
14251 |
Bug |
Increased LDAP filter string size
|
7.08.002 |
14574 |
Bug |
Fix potential segfault at startup in systems with old TSU GbE cards
|
7.08.002 |
14449 |
Bug |
Extended character validation before showing log files in web UI
|
7.08.002 |
14448 |
Bug |
List user names in web UI that are sub strings of system users
|
7.08.002 |
14447 |
Bug |
Do not disclose GPS position anywhere in WEB UI if hiding sensitive info is configured
|
7.08.002 |
14346 |
Bug |
Fixed plausibility check on PTP page when using PRP groups
|
7.08.002 |
14335 |
Bug |
Button 'Show Changes' was not visible for Admin users
|
7.08.002 |
14327 |
Bug |
Moved VSG config option to use PTP TLV from BlackBurst config to Misc tab
|
7.08.002 |
14219 |
Bug |
REST API: Re-enable config write access for admin accounts
|
7.08.002 |
14200 |
Bug |
Added support for MSF182
|
7.08.002 |
14152 |
Bug |
Fixed input validation in URL field in Software Update section of WEB UI
|
7.08.002 |
13934 |
Bug |
Notifications: Send PTP State Change notification for both instances of a dual stack PTP card
|
7.08.002 |
13886 |
Bug |
Fixed FDM configuration in Web UI for two receivers with the same IP
|
7.08.002 |
13802 |
Bug |
Web UI/NTP: Clarify and warn about discarding non-NTS requests
|
7.08.002 |
13796 |
Bug |
SNMP: Include TDOP and PDOP values for second refclock
|
7.08.002 |
13773 |
Bug |
Improved content of error message where minimum password security requirements are checked
|
7.08.002 |
13764 |
Bug |
Notifications now include source IP of sender in all cases
|
7.08.002 |
13503 |
Bug |
Web UI/PTP: Correctly show PSX210 port link state when only an IPv6 address is configured
|
7.08.002 |
13478 |
Bug |
Harmonized format of reflock information on main page of WEB UI
|
7.08.002 |
12730 |
Bug |
Allow firmware update if a USB stick is connected
|
7.08.001 |
12830 |
Feature |
Support for new SyncFire model SF1500
|
7.08.001 |
11599 |
Feature |
Added IPv6 support to multithreaded NTP server on SyncFire
|
7.08.001 |
11429 |
Feature |
Added support for NTS server mode
|
7.08.001 |
7612 |
Feature |
Support for IMS module PSX210
|
7.08.001 |
13507 |
Feature |
Peer certificate verification of external syncmon and microsync is done by default
|
7.08.001 |
13467 |
Feature |
Added description for failed Web login attempt of banned user
|
7.08.001 |
5980 |
Feature |
Calls of curl commands now verify peer certificates by default
|
7.08.001 |
1391 |
Feature |
Improved web UI session handling (form-based auth)
|
7.08.001 |
10395 |
Feature |
Added additional http-methods in clihelp
|
7.08.001 |
13346 |
Feature |
CLI/REST: Added io-ports-menu for the TSU-module
|
7.08.001 |
13313 |
Feature |
CLI/REST: Added io-ports-menu for the FDM180-module
|
7.08.001 |
13288 |
Feature |
Support Daily Jam option for VSI180
|
7.08.001 |
13128 |
Feature |
Support for refclock board GSR183 in variants GPS183, GNS183 and GNS183_UC
|
7.08.001 |
12946 |
Feature |
Added support for IMS module REL1002
|
7.08.001 |
12108 |
Feature |
CLI/REST: Added support to configure IMS BPExxxx modules
|
7.08.001 |
12074 |
Feature |
Multiple SANs can be added to a CSR or certificate by button in the web UI
|
7.08.001 |
11465 |
Feature |
Improved naming of network ports in Web UI to identify ports on LNE cards
|
7.08.001 |
11021 |
Feature |
Added possibility to use customizable login banner
|
7.08.001 |
9862 |
Feature |
Added option to download leap second file via proxy
|
7.08.001 |
7930 |
Feature |
Added xt_LOG module to support optional logging tasks
|
7.08.001 |
2173 |
Feature |
Use gateway of 1st virtual interface as default gateway if no default GW is configured
|
7.08.001 |
1358 |
Feature |
Added descriptive text to decode PTP clock class in WEB UI
|
7.08.001 |
1346 |
Feature |
Improved display of power consumption information in Web UI
|
7.08.001 |
1339 |
Feature |
Removed Statistics page from WEB UI as it is covered by the SyncMon or NTP page
|
7.08.001 |
13500 |
Bug |
CLI Help removed from firmware image to reduce size
|
7.08.001 |
13349 |
Bug |
Selection of access level for new users improved
|
7.08.001 |
12431 |
Bug |
Update of lighttpd to 1.4.68
|
7.08.001 |
11634 |
Bug |
Update of Chrony to 4.2
|
7.08.001 |
12977 |
Bug |
Fixed the appearance of a duplicate firmware entry after deleting a firmware
|
7.08.001 |
9899 |
Bug |
Correction of the displayed scheduled firmware directly after activation
|
7.08.001 |
13823 |
Bug |
SyncMon: Allow hostnames in external SyncMon/microSync address configuration
|
7.08.001 |
13810 |
Bug |
Avoid segmentation fault when importing a json-file
|
7.08.001 |
13752 |
Bug |
SyncMon: Fixed 2nd instance for HPS/PSX cards
|
7.08.001 |
13721 |
Bug |
Avoid unnecessary NTP service restarts
|
7.08.001 |
13708 |
Bug |
Improved validation of an uploaded leapsecond file
|
7.08.001 |
13685 |
Bug |
Fixed disappearing menu-tree in /status/syncteam
|
7.08.001 |
13353 |
Bug |
Fixed objects appearing in every module menu
|
7.08.001 |
13033 |
Bug |
Treat passwords for e-mail authentication like any other password
|
7.08.001 |
12223 |
Bug |
REST/CLI: Menu structure for BPE configuration optimized
|
7.08.001 |
1360 |
Bug |
Improved Set Time procedure on Clock page in Web UI
|
Close LTOS 7.08 Changelog |
Version |
ID |
Typ |
Changelog
|
7.06.014 |
13977 |
Bug |
Initiate web server restart after time jumps
|
7.06.014 |
13943 |
Bug |
CLI/REST: Avoid error messages while setting time-zone of refclock
|
7.06.014 |
13501 |
Bug |
Removed CLIHELP from firmware image
|
7.06.014 |
13441 |
Bug |
Fix potential unresponsive system after adding/changing external NTS servers
|
7.06.014 |
10120 |
Bug |
Make sure all firewall rules are created for all cluster interfaces
|
7.06.014 |
13825 |
Bug |
ntp patches to remedy CVE-2023-26551, CVE-2023-26552, CVE-2023-26553, CVE-2023-26554, CVE-2023-26555
|
7.06.014 |
13811 |
Bug |
Update of tcpdump to 4.99.4
|
7.06.014 |
13717 |
Bug |
Update of sudo to 1.9.13p2
|
7.06.014 |
13713 |
Bug |
Update of curl to 8.0.1
|
7.06.014 |
13471 |
Bug |
Update of OpenSSH to 9.3p1
|
7.06.014 |
12428 |
Bug |
Update of net-snmp to 5.9.4.pre2
|
7.06.014 |
14001 |
Bug |
Fixed maximum string size in SyncMon's address field
|
7.06.014 |
13998 |
Bug |
Support viewing of NTP client list as info user
|
7.06.014 |
13828 |
Bug |
CLI: Fixed segmentation fault when importing a json-file
|
7.06.014 |
13783 |
Bug |
Avoid CPU Error reports that did not exist
|
7.06.014 |
13781 |
Bug |
Remove old VSI statistic files
|
7.06.014 |
13775 |
Bug |
Fixed LTOS version string in LLDP frame
|
7.06.014 |
13774 |
Bug |
Fixed automatic detection of additional power supply
|
7.06.014 |
13762 |
Bug |
CLI/REST: Fixed menu structure for FDM182
|
7.06.014 |
13696 |
Bug |
SyncMon: Avoid redundant notification of Normal Operation state
|
7.06.014 |
13683 |
Bug |
REST API: Fixed disappearing menu-tree in /status/syncteam
|
7.06.014 |
13493 |
Bug |
Corrected behaviour of linkmonitor service during boot phase
|
7.06.014 |
13475 |
Bug |
Always show IMS slot name with physical port on network page
|
7.06.014 |
13472 |
Bug |
SyncMon: Generate alarms for PTPv1 nodes
|
7.06.014 |
13454 |
Bug |
Show fan info on M2000S if system boots with external LDU display
|
7.06.014 |
13452 |
Bug |
Adjusted route example in /config/netconf.cmd
|
7.06.014 |
13352 |
Bug |
CLIHELP: Fixed objects appearing in every module menu
|
7.06.014 |
13350 |
Bug |
Account for configuring additional serial port of refclock in web UI
|
7.06.014 |
13100 |
Bug |
Include ptp_messages file from TSU-GbE in diagnostic file
|
7.06.014 |
12981 |
Bug |
Fixed SNMP IDs for Sync Mon Alert and OK traps
|
7.06.014 |
12282 |
Bug |
Changed wrong behaviour of MRS fixed offset config for NTP source
|
7.06.014 |
11356 |
Bug |
Avoid false configuration of RDT serial refclock type in msc.cfg
|
7.06.013 |
13449 |
Bug |
Fixed memory leak due to increased file count present in 7.06.012
|
7.06.013 |
13228 |
Bug |
Ensure that the SyncMon node status can always be externally read
|
7.06.013 |
13225 |
Bug |
REST: Fixed last-config-change information in /api/status/system
|
7.06.013 |
13179 |
Bug |
REST: Avoid empty nodes in syncmon object
|
7.06.013 |
13084 |
Bug |
Fixed initial refclock time string format on RDT systems
|
7.06.013 |
1903 |
Bug |
Support FAN status on M2000S systems
|
7.06.013 |
13329 |
Bug |
Improved input validation of upload form filename
|
7.06.013 |
12416 |
Bug |
Update of kernel to 4.14.307
|
7.06.013 |
13355 |
Bug |
REST: Object 'module' was sometimes not listed
|
7.06.013 |
13340 |
Bug |
Fixed power supply identification on M2000S systems
|
7.06.013 |
13335 |
Bug |
Fixed import of network config from backup
|
7.06.013 |
13279 |
Bug |
REST: Fixed temperature sensors entries for RSC module on M1000 and M2000S
|
7.06.013 |
12901 |
Bug |
Removed unexpected error message of unknown nts service in the LTOS-light version
|
7.06.012 |
13141 |
Feature |
CLI/REST: Added object 'password-type' to user to specify password encryption algorithm
|
7.06.012 |
13337 |
Bug |
Handle NTP stratum in MRS source correctly if new int.Osc. source is present
|
7.06.012 |
13216 |
Bug |
REST/CLI: Avoid crash of cli service after reading invalid config files
|
7.06.012 |
13207 |
Bug |
Update of curl to 7.88.0
|
7.06.012 |
13174 |
Bug |
Update of libexpat to 2.5.0
|
7.06.012 |
13172 |
Bug |
Update of sudo to 1.9.12p2
|
7.06.012 |
13137 |
Bug |
Update of OpenSSL to 1.1.1t
|
7.06.012 |
12911 |
Bug |
Added curl examples to REST API help
|
7.06.012 |
13221 |
Bug |
Fixed interruption of management service after SHS time limit error on Q7 CPUs
|
7.06.012 |
13210 |
Bug |
Improved PTP BMCA behaviour in Auto mode in case other references are present
|
7.06.012 |
13205 |
Bug |
REST/CLI: Show correct min/max frequency of FDM module
|
7.06.012 |
13163 |
Bug |
Fixed apply of config settings for syslog-ng
|
7.06.012 |
13161 |
Bug |
Avoid multiple notifications to syslog servers in notification/text mode in case more than one syslog server is configured
|
7.06.012 |
13155 |
Bug |
Improved reconnection of USB-attached devices after management service restart
|
7.06.012 |
13144 |
Bug |
Support GNS182 in SNMP MIB
|
7.06.012 |
13142 |
Bug |
Fixed syntax error in SNMP MIB
|
7.06.011 |
13147 |
Feature |
Introduced internal oscillator as dedicated MRS ref type
|
7.06.011 |
13149 |
Bug |
Improved PTP Auto mode behaviour in holdover and free-run mode
|
7.06.011 |
13120 |
Bug |
REST/CLI: Correctly formated PTP master offset
|
7.06.011 |
13129 |
Bug |
Update of bind to 9.16.37
|
7.06.011 |
13146 |
Bug |
Show all stratus bits of holdover state in syslog
|
7.06.011 |
13080 |
Bug |
REST/CLI: Show options of enable flags correctly
|
7.06.010 |
12107 |
Feature |
REST/CLI: Added support for CPE card
|
7.06.010 |
13102 |
Bug |
Check all firmware prerequisites before applying an upgrade
|
7.06.010 |
13108 |
Bug |
Improved firmware signing check
|
7.06.010 |
12995 |
Bug |
Update of curl to 7.87.0
|
7.06.010 |
13124 |
Bug |
Fixed warmed_up state info for CLK2 in SyncMon
|
7.06.010 |
12915 |
Bug |
REST/CLI: Handle HPS100 status correctly on M900 devices
|
7.06.009 |
13022 |
Feature |
Updated leap_second file, expires 2023-12-28 |
7.06.009 |
13028 |
Feature |
Root-CA-Bundle updated to Revision 2023-01-10 |
7.06.009 |
12913 |
Bug |
REST-API: PATCH login shell or group works again |
7.06.009 |
12908 |
Bug |
Fixed saving config of second HPS instance |
7.06.009 |
12898 |
Bug |
Avoid automatic reboots on SyncFires without refclocks |
7.06.009 |
12976 |
Bug |
Indicate PTP sync loop in MRS state |
7.06.009 |
12912 |
Bug |
REST-API: Fixed return codes in users section |
7.06.009 |
12987 |
Bug |
Avoid notification for changed SyncE config that did not happen |
7.06.009 |
12978 |
Bug |
Fixed error of nslookup and host |
7.06.009 |
12973 |
Bug |
REST API: Fixed PUT command to show fw version |
7.06.009 |
12949 |
Bug |
Fixed delayed status change on PTP cards after transitioning into holdover |
7.06.009 |
12943 |
Bug |
Ensure REST API can be disabled via web UI |
7.06.009 |
12941 |
Bug |
Fixed power supply detection on LANTIME M150 |
7.06.009 |
12906 |
Bug |
Fixed PTP "Disabled" mode in config in case "Disable BC Mode" was activated |
7.06.008 |
12321 |
Feature |
Made file system and partition information available in REST/CLI
|
7.06.008 |
11346 |
Feature |
Support configurable delay between SyncMon PTP requests on HPS100
|
7.06.008 |
8732 |
Feature |
CLI-help examples improved
|
7.06.008 |
12513 |
Feature |
Added CPU temperature in REST-API
|
7.06.008 |
12408 |
Feature |
Support for new LANTIME model M150
|
7.06.008 |
12406 |
Feature |
Support for new LANTIME model M250
|
7.06.008 |
12061 |
Feature |
Support disabling BC mode for HPS100 cards
|
7.06.008 |
11481 |
Feature |
Support creating a PRP group of two HPS100 cards
|
7.06.008 |
12339 |
Bug |
Update of OpenSSL to 1.1.1s
|
7.06.008 |
12206 |
Bug |
Update of OpenSSH to 9.1p1
|
7.06.008 |
11439 |
Bug |
Fixed usage of DHCP-CLIENT-ID parameter
|
7.06.008 |
12419 |
Bug |
Update of sudo to 1.9.12p1
|
7.06.008 |
12417 |
Bug |
Update of lighttpd to 1.4.67
|
7.06.008 |
12415 |
Bug |
Update of curl to 7.86.0
|
7.06.008 |
12414 |
Bug |
Update of bind to 9.16.34
|
7.06.008 |
12298 |
Bug |
Update of dbus to 1.12.24
|
7.06.008 |
12341 |
Bug |
External Syslog IP protocol is configured to try IPv4 and IPv6 addresses
|
7.06.008 |
12299 |
Bug |
Update of dhcp to 4.1-esv:r16-p2
|
7.06.008 |
12278 |
Bug |
Update of zlib to 1.2.13
|
7.06.008 |
12839 |
Bug |
Avoid message that reports no connection to lantimed in REST/CLI
|
7.06.008 |
12832 |
Bug |
Fixed procedure to discard a config change
|
7.06.008 |
12814 |
Bug |
Show SyncE ref source in REST/CLI correctly
|
7.06.008 |
12810 |
Bug |
Fixed Meta-BMCA when using multiple PTP Slave cards
|
7.06.008 |
12727 |
Bug |
Fixed warning for https certificates with validity longer than 10 years
|
7.06.008 |
12725 |
Bug |
Do not allow Hybrid mode for PTP L2 configs
|
7.06.008 |
12631 |
Bug |
Corrected state of selected PTP Slave in SyncMon
|
7.06.008 |
12630 |
Bug |
Added PTP loop detection when using multiple PTP Slave cards
|
7.06.008 |
12515 |
Bug |
Improved display of sync state on main page in Web UI
|
7.06.008 |
12508 |
Bug |
Fixed display of events in REST API
|
7.06.008 |
12480 |
Bug |
Fixed handling of two clocks in REST API
|
7.06.008 |
12455 |
Bug |
Fixed PTP loop detection algorithm when using multiple cards
|
7.06.008 |
12454 |
Bug |
Web config changes in MRS priorities are now reflected in REST API
|
7.06.008 |
12430 |
Bug |
Fixed setting of serial port parameters via CLI
|
7.06.008 |
12426 |
Bug |
Fixed setting of external NTP servers via CLI and REST
|
7.06.008 |
12421 |
Bug |
Correct use of restricted_access configuration by REST API
|
7.06.008 |
12402 |
Bug |
Log config changes in REST API
|
7.06.008 |
12400 |
Bug |
Avoid restarts of HPS100 cards that are not affected by a config change of other cards
|
7.06.008 |
12399 |
Bug |
Fixed commit of network services object in REST API and CLI
|
7.06.008 |
12316 |
Bug |
Added robustness when configuring a lot of HPS100 cards in one chassis
|
7.06.008 |
12297 |
Bug |
Fixed SSH login for RADIUS users
|
7.06.008 |
12221 |
Bug |
Added MRS object in REST API for 2nd clock
|
7.06.008 |
12202 |
Bug |
Fixed PPO config in REST API
|
7.06.007 |
7124 |
Feature |
Support PTPv1 nodes in SyncMon
|
7.06.007 |
11948 |
Feature |
Support non-zero exit codes when calling lt_cli in case of an error
|
7.06.007 |
11954 |
Bug |
Update of nss_pam_ldap to 0.9.12
|
7.06.007 |
11945 |
Bug |
Update of OpenLDAP to 2.6.3
|
7.06.007 |
11811 |
Bug |
Fixed VLAN setting for lptp service
|
7.06.007 |
11779 |
Bug |
Test LDAP connection works with special characters now
|
7.06.007 |
11710 |
Bug |
Fixed event notifications config in lt_cli
|
7.06.007 |
11101 |
Bug |
Correct number of root ca bundle checksum entries in syslog-ng.conf
|
7.06.007 |
2658 |
Bug |
Fixed time zone configuration for 2nd FDM card
|
7.06.007 |
11934 |
Bug |
Improvement of load times during save config procedure
|
7.06.007 |
11943 |
Bug |
Update of rsync to 3.2.5
|
7.06.007 |
11929 |
Bug |
Update of zlib to 1.2.12.1
|
7.06.007 |
11923 |
Bug |
Updated Linux Kernel to version 4.14.292
|
7.06.007 |
11972 |
Bug |
Charset for LDAP passwords extended
|
7.06.007 |
2771 |
Bug |
Fixed FDM Flags display format in WEB UI
|
7.06.007 |
12116 |
Bug |
Removed references to fan controls on devices without fans
|
7.06.007 |
12102 |
Bug |
Fixed setting the display time zone via API
|
7.06.007 |
12097 |
Bug |
Switching fans do not errornously trigger fan failure events anymore
|
7.06.007 |
12076 |
Bug |
Fixed ntp.conf that could be incorrect after reboot on systems with 2 refclocks and enabled SHS feature
|
7.06.007 |
12069 |
Bug |
REST/CLI: Fixed temporary missing NTP status/config objects
|
7.06.007 |
11932 |
Bug |
NTPD will not use PTP input via SHM driver in case PTP time is declared invalid
|
7.06.007 |
11928 |
Bug |
Fixed default values for SMPTE TLV in ST 2059-2
|
7.06.007 |
11926 |
Bug |
Added additional infos in CLI Help
|
7.06.007 |
11795 |
Bug |
Fixed FAN state in SNMP
|
7.06.007 |
11793 |
Bug |
Submitted radius NAS_IP identifier corrected
|
7.06.007 |
11711 |
Bug |
Fixed detection of 2nd power supply on M300 models with RPS option
|
7.06.007 |
11586 |
Bug |
Support 10 external NTP servers in SNMP MIB
|
7.06.007 |
11521 |
Bug |
Improved readability of MRS sources in SyncMon System Monitoring
|
7.06.007 |
11487 |
Bug |
Improved handling of changed UTC parameters for leap second announcements
|
7.06.007 |
11485 |
Bug |
Fixed LIU config options in Web UI
|
7.06.007 |
10991 |
Bug |
Improved BPE8000 state info in web ui
|
7.06.006 |
11597 |
Bug |
Fixed load balancing for multithreaded NTP server
|
7.06.006 |
11632 |
Bug |
Update of GnuTLS to 3.7.7
|
7.06.006 |
11630 |
Bug |
Update of Nettle to 3.8.1
|
7.06.006 |
11773 |
Bug |
Added lt_cli/REST API attribute /configuration/chassis0/slots/[SLOT-ID]/module/havequick-rx-min-tfom
|
7.06.006 |
11771 |
Bug |
Fixed not accepting parameter change for ims-port-error notification in REST API
|
7.06.006 |
11769 |
Bug |
Fixed REST API not correctly applying changes for IPv4 addresses
|
7.06.006 |
11611 |
Bug |
Fixed handing of changes for FDM modules if more than one module installed
|
7.06.006 |
11605 |
Bug |
Added missing status information for GPS182 and GNS182 modules
|
7.06.006 |
11602 |
Bug |
Fixed misguiding error counter behavior for LNE-Gbe network interfaces
|
7.06.006 |
11601 |
Bug |
Fixed description of Local_REF1-GPS180-GPS-SV-Status graph in SyncMon
|
7.06.006 |
11594 |
Bug |
Fixed naming wrong reference in notifications for MRS sources
|
7.06.006 |
11592 |
Bug |
Fixed wrong status reports for PSU status via SNMP
|
7.06.006 |
11590 |
Bug |
Fixed firmware downgrade handling from 7.06 light to V6 firmware images
|
7.06.006 |
11588 |
Bug |
Fixed non-working REST API on V7.06-light firmware releases
|
7.06.006 |
11527 |
Bug |
Fixed wrong NTP cluster clock class on PZF devices
|
7.06.006 |
11526 |
Bug |
Fixed broken NTP cluster handling of second reference clock
|
7.06.006 |
11461 |
Bug |
Fixed not clearing MRS Source No Signal error
|
7.06.005 |
11571 |
Bug |
Fixed power supply detection for M300/RPS
|
7.06.005 |
11478 |
Bug |
REST API: Mitigation of Internal Server Error under heavy load
|
7.06.004 |
11530 |
Bug |
Fixed power supply detection for M1000S and M2000S
|
7.06.004 |
11479 |
Bug |
REST API: X-Correlation-Id is now returned in response
|
7.06.004 |
11427 |
Bug |
Fixed power supply status for M500
|
7.06.003 |
11494 |
Feature |
leap_second-file updated, expires on 28 June 2023
|
7.06.003 |
11452 |
Bug |
Update of OpenSSL to 1.1.1q
|
7.06.002 |
4314 |
Task |
Added CLI support for older PTP TSU cards
|
7.06.002 |
1556 |
Feature |
Support for downloading SyncMon data via Web UI
|
7.06.002 |
11342 |
Bug |
Update of curl to 7.84.0
|
7.06.002 |
11336 |
Bug |
REST API: Adjusted return code on access requests with Info user rights
|
7.06.002 |
1355 |
Bug |
Fixed refid on MRS systems if external NTP servers are used
|
7.06.001 |
10560 |
Feature |
Added support for GNS182
|
7.06.001 |
10112 |
Feature |
Add NTS client support for MRS devices
|
7.06.001 |
7661 |
Feature |
Introduced faillock notification for banned users
|
7.06.001 |
7646 |
Feature |
Added support for up to 10 external NTP servers
|
7.06.001 |
6602 |
Feature |
Added option to switch cluster master based on PTP port state
|
7.06.001 |
6577 |
Feature |
Support for syn1588PCI card on SyncFire
|
7.06.001 |
5244 |
Feature |
LDAP secondary groups support
|
7.06.001 |
2569 |
Feature |
Generate NTP keys also generates SHA-XXX and AES-CMAC keys
|
7.06.001 |
8080 |
Feature |
Increased size of arp and conntrack table
|
7.06.001 |
3642 |
Feature |
limits.conf is now added to mbg config files
|
7.06.001 |
1825 |
Feature |
Bruteforce mitigation
|
7.06.001 |
1303 |
Feature |
Syslog now supports the use of IPv4/IPv6 TLS connections
|
7.06.001 |
8068 |
Feature |
Unconfigured LDAP results in a info instead of error state
|
7.06.001 |
5678 |
Feature |
Link state indicator in the Phys. LAN Interfaces menu
|
7.06.001 |
4539 |
Feature |
Function is added to test LDAP connection
|
7.06.001 |
1829 |
Feature |
Display signal-to-noise ratio of satallites for GPS180
|
7.06.001 |
11259 |
Feature |
Added detection for latest BPE8xxx variants
|
7.06.001 |
11103 |
Feature |
Support for FDM182
|
7.06.001 |
10200 |
Feature |
Added support for interface-specific IPv6 gateway configruation
|
7.06.001 |
10115 |
Feature |
Introduced changes command in REST API to show pending changes
|
7.06.001 |
9806 |
Feature |
Include FDM Sync Status in notifications
|
7.06.001 |
9718 |
Feature |
Support for XHE chassis in REST API
|
7.06.001 |
8376 |
Feature |
Added support for TFOM with a TCR180 module
|
7.06.001 |
7931 |
Feature |
Added option to force enabling Black Burst output on VSG181
|
7.06.001 |
6920 |
Feature |
Added config option for SSM value behaviour during clock degradation for T1 outputs
|
7.06.001 |
6753 |
Feature |
Added new options for LTC modes on VSG181
|
7.06.001 |
6709 |
Feature |
REST API Interface can be enabled/disabled via the WebGUI now
|
7.06.001 |
6131 |
Feature |
Added support for VSG180 in CLI/REST
|
7.06.001 |
6130 |
Feature |
Added support for VSG181 in CLI/REST
|
7.06.001 |
6126 |
Feature |
Added support for RSG181 module
|
7.06.001 |
5225 |
Feature |
Added option for NTP to force name resolution of servers either via IPv4 or IPv6
|
7.06.001 |
2640 |
Feature |
Support time zone configuration for syslog output to external syslog servers
|
7.06.001 |
1328 |
Feature |
Display Slot of LNE card for dedicated LAN port
|
7.06.001 |
11261 |
Bug |
REST: Fixed PATCH operation in users config
|
7.06.001 |
10754 |
Bug |
Optimized PTP Multicast Auto selection
|
7.06.001 |
10753 |
Bug |
Update of OpenSSH to 9.0p1
|
7.06.001 |
10438 |
Bug |
Update of wpa_supplicant to 2.10
|
7.06.001 |
10392 |
Bug |
REST API: Made handling of URI consistent with or without trailing slash
|
7.06.001 |
10390 |
Bug |
Syslog automatically switchs between ipv4 and ipv6 DNS entries
|
7.06.001 |
10260 |
Bug |
Fixed removal of default gateway settings on HPS100
|
7.06.001 |
9784 |
Bug |
Web server intermediate certificates handling changed
|
7.06.001 |
9458 |
Bug |
Validation of every uploaded certificate in one file
|
7.06.001 |
8746 |
Bug |
RESTAPI return code is changed to 204 if resource has not changed
|
7.06.001 |
8120 |
Bug |
Update of syslog-ng to 3.34.1
|
7.06.001 |
8105 |
Bug |
Update of pam_radius to 1.6.1
|
7.06.001 |
5247 |
Bug |
SSH LoginGraceTime set to 45sec
|
7.06.001 |
11332 |
Bug |
Update of curl to 7.83.1
|
7.06.001 |
11280 |
Bug |
Update of OpenSSL to 1.1.1p
|
7.06.001 |
11105 |
Bug |
Kernel update to 4.14.281
|
7.06.001 |
11020 |
Bug |
Mitigation of user enumeration attacks
|
7.06.001 |
10533 |
Bug |
Update of lighttpd to 1.4.64
|
7.06.001 |
10491 |
Bug |
Update of rsync to 3.2.4
|
7.06.001 |
10489 |
Bug |
Update of libgd to 2.3.3
|
7.06.001 |
10488 |
Bug |
Update of jansson to 2.14
|
7.06.001 |
10487 |
Bug |
Update of inetutils to 2.2
|
7.06.001 |
10486 |
Bug |
Update of dhcp client to 4.1-esv:r16-p1
|
7.06.001 |
10484 |
Bug |
Gnu binutils removed
|
7.06.001 |
10483 |
Bug |
Update of bind to 9.11.37
|
7.06.001 |
10123 |
Bug |
Program vim removed
|
7.06.001 |
8224 |
Bug |
Update of libssh to 0.9.6
|
7.06.001 |
8104 |
Bug |
Update of pam_radius to 2.0.0
|
7.06.001 |
7533 |
Bug |
Update of ncurses to 6.3
|
7.06.001 |
7532 |
Bug |
Update of nettle to 3.7.3
|
7.06.001 |
5122 |
Bug |
Update of graphicsmagic to 1.3.36
|
7.06.001 |
5119 |
Bug |
Update of tar to 1.34
|
7.06.001 |
5118 |
Bug |
Update of pcre to 8.44
|
7.06.001 |
5117 |
Bug |
Update of OpenLDAP to 2.4.58
|
7.06.001 |
5116 |
Bug |
Update of json_c to 0.15
|
7.06.001 |
5112 |
Bug |
Update of cpio to 2.13
|
7.06.001 |
5110 |
Bug |
Update of bash to 5.1
|
7.06.001 |
3314 |
Bug |
additional network config and user defined notifications are disabled by default
|
7.06.001 |
2437 |
Bug |
Update of shellinabox to post-2.20 4f0ecc3 commit
|
7.06.001 |
2436 |
Bug |
"""uuencode"" and ""uudecode"" removed"
|
7.06.001 |
2432 |
Bug |
Update of net-snmp to 5.9
|
7.06.001 |
2427 |
Bug |
Update of glib to 2.68.1
|
7.06.001 |
2426 |
Bug |
Update of dhcp client to 4.1-esv:r16
|
7.06.001 |
2421 |
Bug |
Update of avahi to 0.8
|
7.06.001 |
10381 |
Bug |
Fixed value in date of recording for NTP client list
|
7.06.001 |
9303 |
Bug |
Scheduled firmware is not possible to be deleted anymore
|
7.06.001 |
4541 |
Bug |
"""cfgreload ldap"" rebuilds nslcd.conf"
|
7.06.001 |
2726 |
Bug |
Session timer in web interface and also honored on auto refreshing SyncMon sites
|
7.06.001 |
11278 |
Bug |
Fixed SMPTE PTP TLV next jump event calculation
|
7.06.001 |
11273 |
Bug |
Fixed field strength display for WWVB on Web UI main page
|
7.06.001 |
11116 |
Bug |
Offer PTP One Step option if profile allows it
|
7.06.001 |
11112 |
Bug |
Fixed generation of SSH keys via REST API and CLI
|
7.06.001 |
11107 |
Bug |
Fixed config option to set default gateway on TSU-GbE and PXA270
|
7.06.001 |
11093 |
Bug |
Fixed oscillator warmed up state in REST/CLI
|
7.06.001 |
10930 |
Bug |
Update of Linux-PAM to 1.5.2
|
7.06.001 |
10556 |
Bug |
CLI/REST: Update service status correctly
|
7.06.001 |
10510 |
Bug |
Update of dbus to 1.12.22
|
7.06.001 |
10446 |
Bug |
Reset PTP Error message if the state is not present anymore
|
7.06.001 |
10387 |
Bug |
Support more than two PPS inputs as MRS sources
|
7.06.001 |
10259 |
Bug |
Prioritize GNSS clocks over PZF clocks in redundant systems if PZF is CLK2
|
7.06.001 |
10250 |
Bug |
Refresh certificate check after config backup
|
7.06.001 |
9785 |
Bug |
Web server configuration paramters renamed
|
7.06.001 |
5612 |
Bug |
Additional LDAP config check before starting the service
|
7.06.001 |
5599 |
Bug |
NTP restarts every time the configuration is changed, even if the change is unrelated to NTP
|
7.06.001 |
5134 |
Bug |
network link status incorrectly represented by network LED
|
7.06.001 |
4388 |
Bug |
Hardening of access rights on flash
|
Close LTOS 7.06 Changelog |
Version |
ID |
Typ |
Changelog
|
7.04.018 |
11120 |
Feature |
Added support for the x182 module family
|
7.04.018 |
11111 |
Bug |
Fixed SSH key generation via REST/CLI
|
7.04.018 |
10993 |
Bug |
Fixed config backup on systems with previously configured PRP interfaces
|
7.04.018 |
10863 |
Bug |
Avoid unneccessary log message for GPS system position
|
7.04.018 |
10749 |
Bug |
Fixed config for ESI ITU limit checks
|
7.04.017 |
10919 |
Bug |
Update of OpenSSL to 1.1.1o
|
7.04.017 |
10951 |
Bug |
Made GNSS types selection configurable via REST and CLI
|
7.04.017 |
10932 |
Bug |
Fixed import/export function in CLI
|
7.04.017 |
10900 |
Bug |
Kernel Bug when decommissioning a PRP group
|
7.04.017 |
10563 |
Bug |
Fixed potentially wrong link speed info for HPS on Web UI main page
|
7.04.016 |
10397 |
Bug |
Update of zlib to 1.2.12
|
7.04.016 |
10681 |
Bug |
Corrected link state on main page for LACP bonding
|
7.04.016 |
10677 |
Bug |
Notification events are now saved correctly on BPE cards with a relay
|
7.04.016 |
10561 |
Bug |
REST API: Added notification-snmp for info users
|
7.04.016 |
10443 |
Bug |
Avoid internal server error after saving the Security page in the web UI
|
7.04.015 |
10207 |
Bug |
Update of OpenSSH to 8.9p1
|
7.04.015 |
10383 |
Bug |
Update of libexpat to 2.4.7
|
7.04.015 |
10270 |
Bug |
Fixed IP string comparisons in access restrictions
|
7.04.015 |
10206 |
Bug |
Update of OpenSSL to 1.1.1n
|
7.04.015 |
10161 |
Bug |
Authorization via REST API improved
|
7.04.015 |
10147 |
Bug |
Login checks via REST API improved
|
7.04.014 |
9702 |
Bug |
System position in REST API works correctly in GPS180-based systems
|
7.04.014 |
8596 |
Bug |
Improved bash command show-lantimelog -m
|
7.04.013 |
10121 |
Bug |
Fixed PTP Monitoring config in SyncMon
|
7.04.013 |
10117 |
Bug |
Re-added english manuals in web ui
|
7.04.013 |
9980 |
Bug |
Fixed reading SyncFire SF1200 temperature sensor
|
7.04.012 |
9779 |
Feature |
Implemented loop detection for NTP if using NTP as MRS Input
|
7.04.012 |
9634 |
Feature |
Allow sending big time offset to reference clocks via CLI
|
7.04.012 |
9628 |
Bug |
Fixed SyncMon trigger counter for offset limit violation if counter is greater than 1
|
7.04.012 |
9609 |
Bug |
Fixed gateway config of HPS100 cards in REST API
|
7.04.012 |
9973 |
Bug |
Include missing event name in notifications sent to an external VP100 display
|
7.04.012 |
9824 |
Bug |
Avoid daily kernel log message while unmounting flash storage
|
7.04.012 |
9819 |
Bug |
Fixed setting HPS100 operating mode via REST API
|
7.04.012 |
9612 |
Bug |
Fixed command for resetting the error relay
|
7.04.012 |
9608 |
Bug |
"Fixed behaviour of ""Monitor Interface"" config option for PTP modules"
|
7.04.012 |
9604 |
Bug |
Launch of lantime management service could be delayed after startup
|
7.04.012 |
9603 |
Bug |
Fixed default gateway config on TSU-GbE modules
|
7.04.012 |
9391 |
Bug |
PIO I/O direction can now be set via REST API
|
7.04.011 |
9469 |
Feature |
Support for new module GPS182
|
7.04.011 |
9351 |
Bug |
Improved checks on ls_announcement file
|
7.04.011 |
9304 |
Bug |
Fixed reading PTP state via SNMP
|
7.04.011 |
9298 |
Bug |
Adjusted antenna cable delay compensation constant for GNS181_UC receiver
|
7.04.010 |
9242 |
Bug |
Content-Type Header not sent by REST API (in fastcgi mode)
|
7.04.010 |
8882 |
Bug |
Ensure that system position is kept after a loss of GNSS in AUTO mode
|
7.04.010 |
9072 |
Bug |
Privileged commands could be accessed by info and admin user in 7.04.009
|
7.04.010 |
8920 |
Bug |
syscheck script did not correct work during NTP startup phase
|
7.04.010 |
8548 |
Bug |
wrong system position value in REST-API
|
7.04.009 |
8754 |
Feature |
Added discovery option for NMS
|
7.04.009 |
8053 |
Feature |
Added NTP Software mode config option in CLI and REST API
|
7.04.009 |
8730 |
Bug |
Account for old SPT cards that are errornously reporting to be in IO slot
|
7.04.009 |
8603 |
Bug |
Fixed transport of gateway config for HPS cards
|
7.04.009 |
8220 |
Bug |
Fixed Event Time Scale config for SMPTE profile
|
7.04.009 |
8718 |
Bug |
Do not open cluster port if cluster is disabled
|
7.04.009 |
8879 |
Bug |
Correctly save misc config file via REST API
|
7.04.009 |
8876 |
Bug |
Do not interrupt http(s) service while enabling or disabling REST API
|
7.04.009 |
8873 |
Bug |
Fixed some plausibility checks on PTP config
|
7.04.009 |
8706 |
Bug |
Include REST API and CLI documentation
|
7.04.009 |
8111 |
Bug |
Fixed link indication on Web UI main page for bonded interfaces
|
7.04.009 |
8075 |
Bug |
Display CLIHELP correctly if available
|
7.04.009 |
8055 |
Bug |
Fixed announce receipt timeout enum values in CLI
|
7.04.009 |
8052 |
Bug |
Fixed HPS operating mode in CLI and REST API
|
7.04.008 |
7400 |
Bug |
Limit length of strings to Open SSL's specification when generating CSR/Certificates
|
7.04.008 |
7665 |
Bug |
Fixed PTP network config in REST API
|
7.04.008 |
7658 |
Bug |
Enable configuration of fixed offset for IRIG source in Web UI
|
7.04.008 |
7649 |
Bug |
Fixed progr. pulse length config in REST API
|
7.04.007 |
7335 |
Bug |
Update of OpenSSH to 8.8
|
7.04.007 |
7489 |
Bug |
Support SF1200 RDT model
|
7.04.007 |
7348 |
Bug |
Serial console port did not work on M100
|
7.04.007 |
7346 |
Bug |
Improved security on NTP leap second file download
|
7.04.007 |
7345 |
Bug |
Activating automatic NTP leap second file download does not require a reboot
|
7.04.007 |
7186 |
Bug |
REST API: Fixed configuring netmask
|
7.04.006 |
6772 |
Feature |
Added basic support for new VSG181H module
|
7.04.006 |
6754 |
Feature |
Support new LTC config flags for VSG181
|
7.04.006 |
6576 |
Feature |
PTPv1 now allows 4 Syncs/s -> DANTE compatibility mode
|
7.04.006 |
6502 |
Feature |
Introduced individual time offset config option for ntpd
|
7.04.006 |
6301 |
Feature |
REST API can now be disabled/enabled via the WebGUI
|
7.04.006 |
6780 |
Bug |
Improved external NTP server selection for MRS
|
7.04.006 |
6744 |
Bug |
Missing radius MBG_Priv_Lvl do not cause a web server crash anymore
|
7.04.006 |
6740 |
Bug |
Update of OpenSSH to 8.7p1
|
7.04.006 |
6574 |
Bug |
Fixed MRS signal available state for PTP
|
7.04.006 |
6712 |
Bug |
Update of OpenSSL to 1.1.1l
|
7.04.006 |
6571 |
Bug |
REST-API and scp/ssh did not honor the disableRootLogin parameter
|
7.04.006 |
6303 |
Bug |
Admin users are not allowed to delete system users anymore
|
7.04.006 |
6257 |
Bug |
"""Save config as"" and ""delete config"" can only access predefined directories "
|
7.04.006 |
6050 |
Bug |
New Linux kernel version 4.14.243
|
7.04.006 |
6781 |
Bug |
Fixed SyncMon integration for HPS cards with PL-A,-B-,-C
|
7.04.006 |
6769 |
Bug |
Avoid re-occuring get_leap_second_date message
|
7.04.006 |
6732 |
Bug |
Adjusted default button on System page to avoid unwanted reboot
|
7.04.006 |
6729 |
Bug |
Allow config backup name lengths of more than 70 chars
|
7.04.006 |
6596 |
Bug |
Enable sshd after factory reset
|
7.04.006 |
6589 |
Bug |
DisableRootLogin had no effect for SCP connections
|
7.04.006 |
6568 |
Bug |
Support GNM181 in an M300
|
7.04.006 |
6096 |
Bug |
Fixed terminal port connection on non-modular servers
|
7.04.006 |
5241 |
Bug |
Fixed antenna faulty event in SyncMon for MSF time servers
|
7.04.006 |
5131 |
Bug |
Fixed bonding state on web ui main page
|
7.04.006 |
4790 |
Bug |
Fixed signal state indication for ESI card inputs in MRS state
|
7.04.006 |
4540 |
Bug |
LDAP configuration error is shown correctly
|
7.04.005 |
6098 |
Feature |
Show LDAP service status in web interface
|
7.04.005 |
5546 |
Feature |
Added timezone for Korea in timezone config
|
7.04.005 |
4944 |
Bug |
Username supports backslash
|
7.04.005 |
6059 |
Bug |
Show IPv4 gateway for HPS100 cards that do not have dual stack support
|
7.04.005 |
6047 |
Bug |
Fixed IPv6 address status for HPS cards
|
7.04.005 |
5780 |
Bug |
netconfig did not correctly identify itself / version string stated LTOS6
|
7.04.005 |
5605 |
Bug |
Re-enabled satellite visibility map
|
7.04.005 |
5187 |
Bug |
Fixed error message when showing ntp key file in web ui
|
7.04.005 |
4975 |
Bug |
Fixed slot type info on notification page for selected IMS chassis
|
7.04.004 |
5594 |
Bug |
Fixed SyncMon node list if group id >=1024
|
7.04.004 |
5542 |
Bug |
SyncFire network interface settings (udp4 hashing and queues) changed
|
7.04.004 |
5598 |
Bug |
NTP avoids unnecessary restarts at configuration change if it is unrelated to NTP
|
7.04.004 |
5588 |
Bug |
Fixed multi-select function in SyncMon
|
7.04.004 |
5564 |
Bug |
SyncFire model SF1100 is now correctly identified
|
7.04.004 |
5563 |
Bug |
The NTP Cluster feature now works stable on RDT models
|
7.04.003 |
5558 |
Bug |
Added input validation for PTP VLAN ID config
|
7.04.002 |
4971 |
Feature |
Support dual PTP Instances for HPS100 modules
|
7.04.002 |
1795 |
Feature |
Added IPv6 network status for PTP cards
|
7.04.002 |
1794 |
Feature |
Support IPv6 gateway configuration for PTP cards
|
7.04.002 |
4970 |
Bug |
Update of OpenSSH to 8.6p1
|
7.04.002 |
4158 |
Bug |
Update of tcpdump to 4.99.0
|
7.04.002 |
2441 |
Bug |
Update of vim to 8.2.2800
|
7.04.002 |
2435 |
Bug |
Update of rsync to 3.2.3
|
7.04.002 |
2430 |
Bug |
Update of web server to lighttpd 1.4.59
|
7.04.002 |
2425 |
Bug |
Update of bzip to 1.0.8
|
7.04.002 |
2422 |
Bug |
Update of bind to 9.11.29
|
7.04.002 |
4893 |
Bug |
Sudo authentication and syslog logging of cron jobs fixed
|
7.04.001 |
2543 |
Feature |
Introduced REST API
|
7.04.001 |
4193 |
Bug |
Update of jansson to 2.13.1
|
7.04.001 |
4873 |
Bug |
Improvement of ntp response rate on SyncFire models
|
Close LTOS 7.04 Changelog |
Version |
ID |
Typ |
Changelog |
7.02.004 |
5561 |
Bug |
NTP cluster works stable on RDT models |
7.02.004 |
5560 |
Bug |
SyncFire model SF1100 is now correctly identified |
7.02.003 |
4787 |
Bug |
LDAP filter and mapping string parsing corrected |
7.02.003 |
4546 |
Bug |
Fix for Syncmon/Graphical representation of sensor data |
7.02.003 |
4545 |
Bug |
Update of OpenSSH to 8.5p1 |
7.02.003 |
4404 |
Bug |
Charset extended to support OpenLDAP binddn |
7.02.003 |
4250 |
Bug |
CSR and Certificate now contain "Extended Key" "TLS Web Server Authentication" |
7.02.003 |
4245 |
Bug |
Fixed Syncmon 'Show Status of Current day' |
7.02.003 |
4882 |
Bug |
Update of OpenSSL to 1.1.1k |
7.02.003 |
4246 |
Bug |
File permission of /etc/group and /etc/hosts hardened |
7.02.003 |
4908 |
Bug |
RADIUS and TACACS timeout parameter did not work |
7.02.003 |
4901 |
Bug |
Fix for REL1000 relay card |
7.02.003 |
4897 |
Bug |
REST-API: show-alarms command fixed (wrong output) |
7.02.003 |
4880 |
Bug |
Wrong clock class in NTP cluster for GNS cards |
7.02.003 |
4789 |
Bug |
ESI input state representation fixed on MRS status page |
7.02.003 |
4709 |
Bug |
REST-API: Fix for status of clk1 slot |
7.02.003 |
4676 |
Bug |
CLI: wrong port representation for CPU interfaces fixed |
7.02.003 |
4675 |
Bug |
CLI: fixed unnecessary error/warning messages during startup |
7.02.003 |
4425 |
Bug |
Fix: wrong representation of state in systems with redundant clock modules |
7.02.003 |
4421 |
Bug |
Fix: Fieldlength for leap second file download URL too short |
7.02.003 |
4391 |
Bug |
Fix: Syncmon report of selected nodes function did not work |
7.02.003 |
4380 |
Bug |
CLI: some 'show' commands did not work as expected |
7.02.003 |
4377 |
Bug |
CLI/REST-API: fixed support for M300/XL RDT |
7.02.003 |
4312 |
Bug |
WebUI: Fixed auto-expand for some web pages |
7.02.002 |
4212 |
Bug |
Fixed VSI offset representation in SyncMon |
7.02.002 |
4156 |
Bug |
Improved error handling for SCG cards with different features |
7.02.002 |
4257 |
Bug |
SSH ECDSA keys are now correctly generated after factory reset |
7.02.002 |
4157 |
Bug |
Update of OpenLDAP to 2.4.57 |
7.02.002 |
2438 |
Bug |
Update of sudo to 1.9.5p2 |
7.02.002 |
4088 |
Bug |
Fixed SyncMon where selected nodes were still active after config error |
7.02.002 |
4213 |
Bug |
Fixed calculation of horizontal phase offset for VSG output |
7.02.002 |
4116 |
Bug |
Fixed SNMP return on satellite counts for GNM clock |
7.02.002 |
3983 |
Bug |
Fixed time zone configuration for second FDM in an IMS chassis |
7.02.002 |
2470 |
Bug |
Cluster switches from Slave to Master only if internal NTP offset is better than 500µs |
7.02.001 |
4061 |
Feature |
Added support for SCG181 |
7.02.001 |
3689 |
Feature |
Check data partition during system start |
7.02.001 |
1329 |
Feature |
Update of ntpsrv to 2.22 |
7.02.001 |
3385 |
Feature |
Improved firmware signing verification |
7.02.001 |
1389 |
Feature |
SNMP now supports SHA224, SHA256, SHA384, SHA512 and AES192, AES256 |
7.02.001 |
1301 |
Feature |
Integrated support of LDAP(S) |
7.02.001 |
3494 |
Feature |
Added PTP Clock-Class and Clock-Accuracy in SyncMon HPS Statistics |
7.02.001 |
2458 |
Feature |
Support of multiple subject alternative names for csr and certificate generation |
7.02.001 |
3507 |
Feature |
New script for setting device serial number |
7.02.001 |
2881 |
Feature |
Renamed XMR log entries to MRS |
7.02.001 |
2775 |
Feature |
IPv6 Support for remote syslog improved |
7.02.001 |
2669 |
Feature |
automatic saving the NTP driftfile after a powerup (4:05UTC, NTP uptime min. 10 hrs) |
7.02.001 |
2485 |
Feature |
Show Graphs from System Monitoring together with graphs from Nodes and add new graphs to a multigraph |
7.02.001 |
4077 |
Bug |
Correct handling of certificates without ending line break |
7.02.001 |
4035 |
Bug |
Allow config imports from devices with different refclock types |
7.02.001 |
3837 |
Bug |
Made webserver start after reboot more reliable |
7.02.001 |
3499 |
Bug |
Update of OpenSSL to 1.1.1h |
7.02.001 |
3398 |
Bug |
Fixed report generation for system monitoring in SyncMon |
7.02.001 |
2769 |
Bug |
Update of Syslog-ng to 3.28.1 |
7.02.001 |
2720 |
Bug |
included in 7.00.010 |
7.02.001 |
2670 |
Bug |
Update of gnuplot to 5.2.8 |
7.02.001 |
4040 |
Bug |
file access rights of https_key.pem changed to 600 |
7.02.001 |
3778 |
Bug |
Owner of files in /usr/share/snmp/mibs/ changed to root |
7.02.001 |
2631 |
Bug |
netcat removed |
7.02.001 |
2433 |
Bug |
lib nettle removed |
7.02.001 |
2428 |
Bug |
lib gnutls removed |
7.02.001 |
2424 |
Bug |
Update of bird to 2.0.7 |
7.02.001 |
1820 |
Bug |
libgcrypt removed |
7.02.001 |
1818 |
Bug |
Update of libpng to 1.6.37 |
7.02.001 |
1816 |
Bug |
Update of gdlib to 2.3.0 |
7.02.001 |
1815 |
Bug |
Removed libfreetype - no longer required |
7.02.001 |
1813 |
Bug |
Update of GraphicsMagick to 1.3.35 |
7.02.001 |
1812 |
Bug |
Xtrastats removed |
7.02.001 |
1810 |
Bug |
Kernel hardening recommended by lynis |
7.02.001 |
1806 |
Bug |
Linux kernel updated to 4.14.187 |
7.02.001 |
1700 |
Bug |
Update of TLS cipher suites to disable CBC |
7.02.001 |
1306 |
Bug |
Hiding additional sensitive information in diag file |
7.02.001 |
3486 |
Bug |
Account for changes on IPv6 access restrictions in ntp.conf |
7.02.001 |
4072 |
Bug |
CLI did not always display service status correctly |
7.02.001 |
4053 |
Bug |
Improved input validation in SyncMon |
7.02.001 |
4052 |
Bug |
Fixed network interfaces config in startwizard on console |
7.02.001 |
3984 |
Bug |
Allow automatic save as startup for SyncMon |
7.02.001 |
3871 |
Bug |
Fixed syslog server config in M300/M600 front panel |
7.02.001 |
3673 |
Bug |
Avoid repeating debug messages for PTP datasets |
7.02.001 |
3644 |
Bug |
Avoid firmware update problems due to unnecessary disk space usage |
7.02.001 |
3523 |
Bug |
Correctly indicate daylight saving info for southern hemispere time zones |
7.02.001 |
3492 |
Bug |
PTP Slave is now configurable on cards in MRI2 and ESI2 even if 2nd clock is missing |
7.02.001 |
3460 |
Bug |
Email configuration not updated in any case if hostname or domain changed |
7.02.001 |
2761 |
Bug |
false warning message about config changes fixed when logging in as non-root superuser |
7.02.001 |
2649 |
Bug |
included in 7.00.010 |
Close LTOS 7.02 Changelog |